Extruded bars are produced in accordance with TS EN 12165 norm in the production of complex shaped forged parts that require high malleability and good forgeability.
|
Technical Information
|
|||
|---|---|---|---|
|
Tolerances:
|
TS EN 12165 Copper and copper alloys. Wrought and unwrought forging stock
|
||
|
Length:
|
Standart 3000 mm, up to 4000 mm
|
||
|
Packaging:
|
Pvc Covered Bundles or Wooden Cases
|
||
|
Production Dimensions:
|
8-120 mm
|
||
|
Coil Weight:
|
|
||
| EN Symbol | EN No | Cu | Al | As | Fe | Mn | Ni | P | Pb | Si | Sn | Zn | Others Total |
Density g/cm³ |
|
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| CuZn39Pb3 | CW614N | min. | 57,0 | – | – | – | – | – | – | 2,2 | – | – | Remainder | – | 8,4 |
| max. | 59,0 | 0,05 | – | 0,3 | – | 0,3 | – | 3,5 | – | 0,3 | 0,2 | ||||
| CuZn40Pb2 | CW617N | min. | 57,0 | – | – | – | – | – | – | 1,6 | – | – | Remainder | – | 8,4 |
| max. | 59,0 | 0,05 | – | 0,3 | – | 0,3 | – | 2,2 | – | 0,3 | 0,2 | ||||
| CuZn36Pb2As | CW602N | min. | 61,0 | – | 0,02 | – | – | – | – | 1,7 | – | – | Remainder | – | 8,4 |
| max. | 63,0 | 0,05 | 0,15 | 0,1 | 0,1 | 0,3 | – | 2,8 | – | 0,1 | 0,2 | ||||
| CuZn36Pb3 | CW603N | min. | 60,0 | – | – | – | – | – | – | 2,5 | – | – | Remainder | – | 8,5 |
| max. | 62,0 | 0,05 | – | 0,3 | – | 0,3 | – | 3,5 | – | 0,2 | 0,2 | ||||
| CuZn37Pb2 | CW606N | min. | 61,0 | – | – | – | – | – | – | 1,6 | – | – | Remainder | – | 8,4 |
| max. | 63,0 | 0,05 | – | 0,2 | – | 0,3 | – | 2,5 | – | 0,2 | 0,2 | ||||
| CuZn38Pb1 | CW607N | min. | 60,0 | – | – | – | – | – | – | 0,8 | – | – | Remainder | – | 8,4 |
| max. | 61,0 | 0,05 | – | 0,2 | – | 0,3 | – | 1,6 | – | 0,2 | 0,2 | ||||
| CuZn39Pb2 | CW612N | min. | 59,0 | – | – | – | – | – | – | 1,6 | – | – | Remainder | – | 8,4 |
| max. | 60,0 | 0,05 | – | 0,3 | – | 0,3 | – | 2,5 | – | 0,3 | 0,2 | ||||
| CuZn40Pb2Al | CW618N | min. | 57,0 | 0,05 | – | – | – | – | – | 1,6 | – | – | Remainder | – | 8,3 |
| max. | 59,0 | 0,5 | – | 0,3 | – | 0,3 | – | 3,0 | – | 0,3 | 0,2 | ||||
| CuZn43Pb2Al | CW624N | min. | 55,0 | 0,05 | – | – | – | – | – | 1,6 | – | – | Remainder | – | 8,4 |
| max. | 57,0 | 0,5 | – | 0,3 | – | 0,3 | – | 3,0 | – | 0,3 | 0,2 | ||||
| CuZn35Pb1 | CW625N | min. | 62,0 | 0,5 | 0,02 | – | – | – | – | 1,2 | – | – | Remainder | – | 8,4 |
| max. | 64,0 | 0,7 | 0,15 | 0,3 | 0,1 | 0,2 | – | 1,6 | – | 0,3 | 0,2 | ||||
| CuZn33Pb1 | CW626N | min. | 64,0 | 0,8 | 0,02 | – | – | – | – | 1,2 | – | – | Remainder | – | 8,4 |
| max. | 66,0 | 1,0 | 0,15 | 0,3 | 0,1 | 0,2 | – | 1,7 | – | 0,3 | 0,2 | ||||
| CuZn32Pb2AsFeSi | CW709R | min. | 64,0 | – | 0,03 | 0,1 | – | – | – | 1,5 | 0,45 | – | Remainder | – | 8,4 |
| max. | 66,5 | 0,03 | 0,08 | 0,2 | – | 0,3 | – | 2,2 | 0,75 | 0,3 | 0,2 | ||||
| CuZn39AlFeMn | CW721R | min. | 57,0 | 0,3 | – | 0,2 | 0,8 | – | – | 0,8 | – | 0,2 | Remainder | – | 8,63 |
| max. | 59,0 | 1,3 | – | 1,2 | 1,8 | 0,3 | – | 1,6 | – | 1,0 | 0,3 | ||||
| CuZn35Ni3Mn2AlPb | CW710R | min. | 58,0 | 0,3 | – | – | 1,5 | 2,0 | – | 0,2 | – | – | Remainder | – | 8,3 |
| max. | 60,0 | 1,3 | – | 0,5 | 2,5 | 3,0 | – | 0,8 | 0,1 | 0,5 | 0,3 | ||||
| CuZn37Mn3Al2PbSi | CW713R | min. | 57,0 | 1,3 | – | – | 1,5 | – | – | 0,2 | 0,3 | – | Remainder | – | 8,1 |
| max. | 59,0 | 2,3 | – | 1,0 | 3,0 | 1,0 | – | 0,8 | 1,3 | 0,3 | 0,3 | ||||
| CuZn40Mn1Pb1FeSn | CW722R | min. | 56,5 | – | – | 0,2 | 0,8 | – | – | 0,8 | – | 0,2 | Remainder | – | 8,3 |
| max. | 58,5 | 0,1 | – | 1,2 | 1,8 | 0,3 | – | 1,6 | – | 1,0 | 0,3 | ||||
| CuZn36 | CW507L | min. | 63,5 | – | – | – | – | – | – | – | – | – | Remainder | – | 8,4 |
| max. | 65,5 | 0,02 | – | 0,05 | – | 0,3 | – | 0,05 | – | 0,1 | 0,1 | ||||
| CuZn37 | CW508L | min. | 62,0 | – | – | – | – | – | – | – | – | – | Remainder | – | 8,4 |
| max. | 64,0 | 0,05 | – | 0,1 | – | 0,3 | – | 0,1 | – | 0,1 | 0,1 | ||||
| CuZn40 | CW509L | min. | 59,0 | – | – | – | – | – | – | – | – | – | Remainder | – | 8,4 |
| max. | 61,5 | 0,05 | – | 0,2 | – | 0,3 | – | 0,2 | – | 0,2 | 0,2 | ||||
| CuZn42 | CW510L | min. | 57,0 | – | – | – | – | – | – | – | – | – | Remainder | – | 8,4 |
| max. | 59,0 | 0,05 | – | 0,3 | – | 0,3 | – | 0,2 | – | 0,3 | 0,2 | ||||
| CuZn42 Pb 80 ppm | CW510L Pb 80 ppm | min. | 57,0 | – | – | – | – | – | – | – | – | – | Remainder | – | 8,37 |
| max. | 59,0 | 0,05 | – | 0,1 | – | 0,1 | – | 0,008 | – | 0,1 | 0,2 | ||||
| CuZn21Si3P | CW724R | min. | 75,0 | – | – | – | – | – | 0,02 | – | 2,7 | – | Remainder | – | 8,3 |
| max. | 77,0 | 0,05 | – | 0,3 | 0,05 | 0,2 | 0,10 | 0,10 | 3,5 | 0,3 | 0,2 | ||||
| CuZn40SiSn | CF725R | min. | 58,5 | – | – | – | – | – | – | – | 0,2 | 0,2 | Remainder | – | 8,3 |
| max. | 61,5 | 0,01 | – | 0,25 | – | – | – | 0,02 | 0,4 | 0,5 | 0,2 | ||||
| CuZn40MnSi | CF726R | min. | 58,5 | – | – | – | 0,05 | – | – | – | 0,15 | – | Remainder | – | 8,3 |
| max. | 61,5 | 0,01 | – | 0,25 | 0,25 | – | – | 0,02 | 0,4 | 0,2 | 0,2 | ||||
| CuNi7Zn39Pb3Mn2 | C797 | min. | 46,0 | – | – | – | 1,0 | 6,5 | – | 1,5 | – | – | Remainder | – | 8,44 |
| max. | 48,5 | 0,05 | – | 1,0 | 2,5 | 8,5 | – | 2,5 | – | – | 0,3 | ||||
| CuZn31Si1 | CW708R | min. | 66,0 | – | – | – | – | – | – | – | 0,7 | – | Remainder | – | 8,4 |
| max. | 70,0 | – | – | 0,4 | – | 0,5 | – | 0,8 | 1,3 | 0,5 | 0,5 | ||||
| CuZn39Pb1Al | CC754S | min. | 58,0 | – | – | – | – | – | – | 0,5 | – | – | Remainder | – | 8,3 |
| max. | 63,0 | 0,8 | – | 0,7 | 0,5 | 1,0 | 0,02 | 2,5 | 0,05 | 1,0 | – | ||||
| CuZn39Pb1Al (Low Lead) | CC755S | min. | 59,5 | 0,4 | – | 0,05 | – | – | – | 1,2 | – | – | Remainder | – | 8,3 |
| max. | 61,0 | 0,7 | – | 0,2 | 0,05 | 0,2 | – | 1,7 | 0,05 | 0,35 | – |
No alloy matches your search.
EN 12165 Table 17 — Diameter Tolerances for Round Forging Stock
Dimensions in mm.
| Nominal Diameter | Tolerances | ||
|---|---|---|---|
| Over | Up to and including | Class A | Class B |
| 10ᵃ | 18 | ±0,25 | ±0,14 |
| 18 | 30 | ±0,30 | ±0,17 |
| 30 | 50 | ±0,60 | ±0,20 |
| 50 | 80 | ±0,70 | ±0,37 |
| 80 | 120 | ±2 | – |
| 120 | 160 | ±2,5 | – |
ᵃ Including 10.
EN 12165 Table 18 — Straightness Tolerances for Round Forging Stock
| Nominal Diameter | Maximum Deviation from Straightness (mm) | |||
|---|---|---|---|---|
| Over any 400 mm length | Over the total length L of the forging stock in metres (L ≥ 1 m) | |||
| for alloys in Tables 5, 6 and 7 | for alloys in Tables 1, 2, 3, 4 and 8 | for alloys in Tables 5, 6 and 7 | for alloys in Tables 1, 2, 3, 4 and 8 | |
| 10 mm up to and including 60 mm | 1,5 | 3,0 | 3,0 × L | 6,0 × L |
Note: Straightness tolerances for rods over 60 mm diameter shall be agreed between customer and supplier.
Mes Metal continuously improves its service and product quality through effective use of technology, prioritizing customer satisfaction and building a strong international presence.
Operating in the copper alloys sector since 1981, Mes Metal A.Ş. is one of Turkey's leading brass rod manufacturers.
Baksav Sanayi Sitesi, Mustafa Kurdoğlu Cad. No: 22 Beylikdüzü - Istanbul TURKEY
export1@mesmetal.com